84-91 13B Rx7

84-91 13B Mazda Rx7 Exhaust Headers

  • 84-91 N/A 13B Rx7 6-Port Racing Beat Road Race Header (16127)

    84-91 N/A 13B Rx7 6-Port Racing Beat Road Race Header (16127)

    Fits 6 port 13B engines (Non Turbo) Racing Beat

    Racing Beat's Road Racing Header for the 1984-91 RX-7 13B (6-Port) is the first step in building a serious racing exhaust system. The engine-to-pipe flange is laser cut from 1/5" thick flat steel. Like all of the headers we manufacture, the Road Racing Header is constructed with 2" OD mild steel tubing, .120" inch wall thickness, and mandrel-bent tubing throughout.

    Outlet flange gaskets, bolts, and nuts are included. If needed, an engine-to-header gasket is available separately. An Air Control and Check Valve Cover Plate is required when using this header with a stock intake system. The Road Race Header can also be used as the basis for a custom streetable exhaust system in any car from 1971-92 (equipped with a 6-port engine), which allows simple swapping between street and race exhaust systems.

    This header can used with the Street Port Center-Section Pipe 1979-85 12A & 13B except GSL-SE or 1984-85 GSL-SE.

    0.0
    Add first review
    Not rated yet
    • $395.95
    Sorry, we only have 980 of that item available
  • 84-85 13B Rx7 Racing Beat Streetable Header (16013)

    84-85 13B Rx7 Racing Beat Streetable Header (16013)

    This RX-7 Header is designed for a bolt-on installation, when used with the appropriate Power Pulse Presilencer in all 1981-85 RX-7 with 13B conversion or the 1984-85 RX-7 GSL-SE models. The combination of this RX-7 header and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters for use in racing applications, along with any intermediate pieces of tubing. This header includes a mounting flange for the oxygen sensor.

    The Racing Beat RX-7 header assembly is constructed with .120-inch wall, mandrel-bend, mild steel tubing for increased durability and sound suppression. Both flanges are laser-cut from .5-inch thick steel plate for positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed.

    0.0
    Add first review
    Not rated yet
    • $395.95
    Sorry, we only have 984 of that item available
  • 86-88 N/A Rx7 Road Race Header (16128)

    86-88 N/A Rx7 Road Race Header (16128)

    This header has the 6-port actuator pick-up tube & oxygen sensor position for use on a 1986-88 RX-7 13B.

    Road Race Header (w/ 6-port actuator pick-up tube & oxygen sensor position for use on a 1986-88 RX-7 13B) - This model Road Race Header that we offer is intended to bolt-up to the Road Race Presilencer section. Please note: that this header is not compatible with the Street Port Center Section that we offer for the earlier 1984-85 RX-7 GSL-SE - only with the Road Race Presilencer section referenced above. This header is not compatible with the 1988-91 RX-7 convertible chassis equipped with the automatic transmission: the header outlet will make contact with the transmission case.

    Racing Beat's Road Racing Header is the first step in building a serious racing exhaust system. The engine-to-pipe flange is laser cut from 7/16" thick flat steel for superb exhaust gas sealing qualities. Like all of the headers we manufacture, the Road Racing Header is constructed with 2" OD mild steel tubing, .120" wall thickness, and mandrel-bent tubing throughout. This header weighs approximately 15.5 lbs and is approximately 28" in length.

    On the 1986-88 13B 6-Port engines, the auxiliary intake actuators are operated by back pressure from the exhaust system. This header features a back pressure pick-up tube that allows for the correct operation of the 6-port intake actuators. Also included on the header is an oxygen sensor position for cars that require an oxygen sensor for correct operation.

    Outlet flange gaskets, bolts, nuts, AC & CV cover plate, and installation instructions are included. An Engine-to-Header Gasket is not included, but is available separately if needed.

    0.0
    Add first review
    Not rated yet
    • $400.00
    Sorry, we only have 991 of that item available
  • 89-91 Rx7 Racing Beat Road Race Header (16129)

    89-91 Rx7 Racing Beat Road Race Header (16129)

    Road Race Header (w/ oxygen sensor position for use on a 1989-91 RX-7 13B) - This model Road Race Header that we offer is intended to bolt-up to the Road Race Presilencer section. Please note: this header is not compatible with the Street Port Center Section that we offer for the earlier 1984-85 RX-7 GSL-SE - only with the Road Race Presilencer section referenced above.  This header is not compatible with the 1988-91 RX-7 convertible chassis equipped with the automatic transmission:  the header outlet will make contact with the transmission case.

    Racing Beat's Road Racing Header is the first step in building a serious racing exhaust system. The engine-to-pipe flange is laser cut from 7/16" thick flat steel for superb exhaust gas sealing qualities. Like all of the headers we manufacture, the Road Racing Header is constructed with 2" OD mild steel tubing, .120" wall thickness, and mandrel-bent tubing throughout. This header weighs approximately 15.5 lbs and is approximately 28" in length.

    On the 1986-88 13B 6-Port engines, the auxiliary intake actuators are operated by backpressure from the exhaust system. On the later 1989-91 13B 6-Port engines, these actuators are operated by air pressure from the emissions control air pump. Installation of this header does NOT require the removal of the air pump, and therefore the operation of the 6-port actuators are not affected. Included on the header is an oxygen sensor position for cars that require an oxygen sensor for correct operation.

    Outlet flange gaskets, bolts, nuts, and installation instructions are included. An Engine-to-Header gasket is not included, but is available separately if needed.

    0.0
    Add first review
    Not rated yet
    • $310.00
    Sorry, we only have 997 of that item available
  • 86-91 N/A Rx7 Racing Beat Streetable Header (16130)

    86-91 N/A Rx7 Racing Beat Streetable Header (16130)

    Our rotary exhaust Header/Collector is designed for a bolt-on installation, when used with the appropriate Power Pulse Presilencer, in all 1986-91 non-turbo RX-7s. The combination of this Header/Collector and the appropriate presilencer replaces the stock exhaust manifold and all catalytic converters, along with any intermediate pieces of tubing. (In this application, the presilencer will bolt-up to the factory Y-pipe.)

    For optimum performance gains for this application, we recommend that a header be used on an engine configured with a carburetor intake system. For this reason, we suggest another suitable configuration for use on a fuel-injected engine is the Racing Beat Catalytic Converter Replacement Pipe with Presilencer combo. These components offer comparable performance gains, quieter performance and a price advantage as compared with the header/presilencer combination. These components replace only the stock exhaust components located between the stock exhaust manifold and the Y-pipe.

    The Header/Collector assembly is constructed with .120" wall, mandrel-bent, mild steel tubing (2" OD primary, 2.5" OD secondary) for excellent durability and noise suppression. Both flanges are laser cut from 7/16" thick steel plate for positive gas sealing. An outlet gasket is included. An engine-to-header gasket is available separately if needed. This header is equipped with an oxygen sensor fitting.

    0.0
    Add first review
    Not rated yet
    • $395.95
    Sorry, we only have 966 of that item available
  • 13B Disassembled Road Race Header Kit (16212)

    13B Disassembled Road Race Header Kit (16212)

    We offer a Disassembled Road Race Header Kit for customized exhausts or special chassis clearance requirements. Both the 12A and 13B engine kits include: an engine-to-header flange, primary tube #1 and primary tube #2, a U-bend tube section, and an dual-tube outlet flange.

    Flanges are laser-cut mild steel, and the tubing is mandrel bent .120"-wall HREW steel. The addition of the U-bend tube allows for even more flexibility with your design. Gaskets are not provided but are available separately.

    0.0
    Add first review
    Not rated yet
    • $210.95
    Sorry, we only have 992 of that item available

Bestsellers