Intake Manifolds

Mazda Intake Manifolds
  • 74-78 13B Side Draft DCOE Intake Manifold (ARE700)

    74-78 13B Side Draft DCOE Intake Manifold (ARE700)

    Can be used with Weber side draft DCOE style Weber carburetor.

    Gaskets sold separately.

    Comes out 4" off the engine block.

    0.0
    Add first review
    Not rated yet
    • $250.00
    Sorry, we only have 996 of that item available
  • 79-85 12A Rx7 Side Draft DCOE Intake Manifold (ARE701)

    79-85 12A Rx7 Side Draft DCOE Intake Manifold (ARE701)

    Fits Weber 45/48/50 DCOE Carburetors.

    Comes 3" off the engine block.

    0.0
    Add first review
    Not rated yet
    • $250.00
    Sorry, we only have 978 of that item available
  • 84-91 13B N/A Rx7 Side Draft DCOE Intake Manifold (ARE702)

    84-91 13B N/A Rx7 Side Draft DCOE Intake Manifold (ARE702)

    84-91 13B Side Draft Intake Manifold (6 Port)

    Will stick out 4" from the block before a carburetor is attached.

    0.0
    Add first review
    Not rated yet
    • $250.00
    Sorry, we only have 994 of that item available
  • 84-91 13B N/A Rx7 Wrap Over Manifold (ARE705)

    84-91 13B N/A Rx7 Wrap Over Manifold (ARE705)

    84-91 13B 6 Port N/A Wrap Over Intake Manifold to suit Weber carburetor.

    Dyno tested: 213hp @ 7900rpm with a Weber 48 DCOE.

    Height: Lower manifold bolt to upper manifold bolt is 10-1/2"

    Width: Sticks out from the side of the engine 4-1/4"

    0.0
    Add first review
    Not rated yet
    • $425.00
    Sorry, we only have 972 of that item available
  • 71-73 12A Rx7 Holley Carburetor Intake Manifold (16460)

    71-73 12A Rx7 Holley Carburetor Intake Manifold (16460)

    These are made to order, don't expect it in a hurry.

    The Racing Beat-designed intake manifold for the 1971-73 12A Stock and Street-ported engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    Racing Beat manifolds for Holley applications are cast by a local foundry then delivered to our in-house production shop for final machining and surface finishing. Each manifold is hand-machined to match the specific intake port configuration of the intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor intensive processes have been completed these manifolds look as good as they perform!

    This manifold includes a vacuum source for power brakes.

    0.0
    Add first review
    Not rated yet
    • $315.00
    Out of stock
  • 74-78 12A Rx7 Holley Carburetor Intake Manifold (16463)

    74-78 12A Rx7 Holley Carburetor Intake Manifold (16463)

    The Racing Beat-designed intake manifold for the 1974-78 12A Stock and Street-ported engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    All of Racing Beat's manifolds for Holley carburetor applications are sand-cast by a local foundries and delivered to our in-house production shop for all machining and surface finishing processes. Select manifolds are then hand-ported to match a specific intake port configuration for an intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    0.0
    Add first review
    Not rated yet
    • $410.95
    Out of stock
  • 79-85 12A Rx7 Holley Carburetor Intake Manifold (16464)

    79-85 12A Rx7 Holley Carburetor Intake Manifold (16464)

    The Racing Beat-designed intake manifold for the 1979-85 12A Stock and Street-ported engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    All of Racing Beat's manifolds for Holley carburetor applications are sand-cast by a local foundries and delivered to our in-house production shop for all machining and surface finishing processes. Select manifolds are then hand-ported to match a specific intake port configuration for an intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    This manifold includes a vacuum source for power brakes.

    0.0
    Add first review
    Not rated yet
    • $410.95
    Out of stock
  • 87-91 Turbo Rx7 Holley Carburetor Intake Manifold (16475)

    87-91 Turbo Rx7 Holley Carburetor Intake Manifold (16475)

    The Racing Beat-designed intake manifold for the 1987-91 TURBO II engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    All of Racing Beat's manifolds for Holley carburetor applications are sand-cast by a local foundries and delivered to our in-house production shop for all machining and surface finishing processes. Select manifolds are then hand-ported to match a specific intake port configuration for an intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    This manifold includes a vacuum source for power brakes.

    0.0
    Add first review
    Not rated yet
    • $410.95
    Out of stock
  • 84-91 13B N/A Holley Carburetor Intake Manifold (16476)

    84-91 13B N/A Holley Carburetor Intake Manifold (16476)

    From bottom of two center intake ports to carb base plate is 6"

    The Racing Beat-designed intake manifold for the 1984-91 13B 6-Port rotary engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of RX-7 street or custom race applications.

    Please note:  it is highly recommended that the intermediate housing be port-matched to the manifold (P/N 16476) when using this manifold with the 1984-5 13B 6-Port engine configuration.

    All of Racing Beat's 13B intake manifolds for Holley carburetor applications are sand-cast by a local foundries and delivered to our in-house production shop for all machining and surface finishing processes. Select manifolds are then hand-ported to match a specific intake port configuration for an intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    If needed, an engine-to-manifold gasket (1984-85), (1986-88), or (1989-91), and/or Holley base gasket are available separately.

    0.0
    Add first review
    Not rated yet
    • $410.95
    Out of stock
  • 74-78 13B Rx7 Holley Carburetor Intake Manifold (16477)

    74-78 13B Rx7 Holley Carburetor Intake Manifold (16477)

    The Racing Beat-designed intake manifold for the 1974-78 13B Stock Port engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    All of Racing Beat's manifolds for Holley carburetor applications are sand-cast by a local foundries and delivered to our in-house production shop for all machining and surface finishing processes. Select manifolds are then hand-ported to match a specific intake port configuration for an intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    This manifold includes a vacuum source for power brakes.

    0.0
    Add first review
    Not rated yet
    • $410.95
    Out of stock
  • 74-78 13B Rx7 Holley Carburetor Intake Manifold - Street Port (16478)

    74-78 13B Rx7 Holley Carburetor Intake Manifold - Street Port (16478)

    For street ported engines.

    The Racing Beat-designed intake manifold for the 1974-78 13B Street Port rotary engine is ideally suited to meet the performance requirements of the Holley carburetor. Designed by Chief Engineer/Engine Builder Jim Mederer, these cast aluminum intake manifolds have proven themselves in a variety of street and race applications.

    All of Racing Beat's 13B intake manifolds for Holley carburetor applications are sand-cast by a local foundries and delivered to our in-house production shop for all machining and surface finishing processes. Select manifolds are then hand-ported to match a specific intake port configuration for an intended engine application. Further machining is then undertaken to match the base-plate surface to the Holley carburetor base. These critical machining steps ensure a positive fitment between both the engine surface and the carburetor base. Every manifold is then surface finished using a ball-burnishing process that enhances the final appearance of the aluminum material. Once these labor-intensive processes have been completed these manifolds look as good as they perform!

    This manifold includes a vacuum source for power brakes.

    0.0
    Add first review
    Not rated yet
    • $410.95
    Sorry, we only have 1 of that item available
  • 13B Peripheral Port Weber Intake Manifold (16490)

    13B Peripheral Port Weber Intake Manifold (16490)

    The Racing Beat-designed and manufactured Peripheral Port Intake Manifold mates a Weber 48 IDA or 51 IDA downdraft carburetor, or equivalent throttle body, to the Racing Beat-manufactured 13B peripheral port housings. (This manifold cannot be used on the Mazda Factory Race MFR housings.)

    The steel tubing manifold is attached to the rotor housings with hoses that are included. A simple support bracket fabricated for your particular application, typically attached from the carburetor-manifold junction to the threaded bosses on top of the rotor housings, will complete the task.

    0.0
    Add first review
    Not rated yet
    • $375.50
    Out of stock
  • 12A EGR Block Off Plate (ARE8908)

    12A EGR Block Off Plate (ARE8908)

    If you put an earlier incompatible 12A intake manifold or an aftermarket manifold that doesnt account for the center iron EGR port in the 81-85 12A Mazda Rx7, then this will accomodate you.

    Block off the EGR port on 81-85 12A engines without tearing the motor apart to do so.

    You will probably need some intake manifold gaskets and intake manifold o-rings as well.

    0.0
    Add first review
    Not rated yet
    Regular Product
    • $65.00
    Sorry, we only have 994 of that item available

Bestsellers